10x14 Gable Shed Plans
A 10x14 gable shed (a 14x10 shed, written the other way round) gives you 140 square feet of storage and costs from $4,540 in materials. The plans for this exact size: every cut, every board to buy, 16 build steps in 3D and printable drawings.
10x14 versus 14x10: the front matters
Here width means left to right when you face the front door. Depth runs from front to back. The size label describes the footprint; it does not specify which wall faces you.
This plan has a 10-foot front and 14-foot depth. The ridge runs front to back; the two roof slopes span half the width on each side. A 14-foot front and 10-foot depth still has 140 square feet, but changes the rafter span, ridge length and wall layout. Rotating a finished shed is different from swapping these design inputs.
| Output | 10-ft front × 14-ft depth | 14-ft front × 10-ft depth |
|---|---|---|
| Floor area | 140 sq ft | 140 sq ft |
| Roof area | 189 sq ft | 188 sq ft |
| Overall height | 11' 11-15/16" | 12' 11-15/16" |
| Boards to buy | 145 | 139 |
| Sheets to buy | 29 | 29 |
| Required materials estimate | $4,540 | $4,528 |
Open this exact configuration or try the alternate orientation. Each link recalculates its own materials; do not reuse one layout’s shopping list for the other.
Both include a framed floor, wall and roof materials, siding, roofing, door hardware, fasteners and finishing. They share treated skids on gravel, LP SmartSide siding, asphalt shingles, moderate snow setting, 6-inch overhang, a front double door (62 × 80-inch rough opening) and one 24 × 36-inch window on the left wall. No structural approval is implied.
Estimates use built-in 2025–26 US prices and exclude optional items, labor, tools, permits, tax and delivery. Check local wind/snow loads, setbacks, permits and foundation requirements with your building department or a qualified professional. For the roof-style decision, see the controlled gable versus lean-to comparison.
What you get
What's inside the 10x14 plans
Part of the plan the designer makes for this 10x14 gable shed: the framing drawing of the front wall, the start of the cut list and the build steps. Change the door, windows, roof or any dimension and every number, cut and drawing is calculated again.
From the cut list
| Qty | Stock | Length | Used for |
|---|---|---|---|
| 3 | PT 4x6 | PT 4x6 @ 168" | Skid (PT 4x6 on edge, ground-contact rated) |
| 2 | PT 2x6 | PT 2x6 @ 168" | Rim joist |
| 12 | PT 2x6 | PT 2x6 @ 117" | Band joist (front/back), Floor joist @ 16" o.c. |
| 2 | 2x10 | 2x10 @ 65" | Header 2-2x10 (door) |
| 3 | 2x8 | 2x8 @ 177" | Ridge board 2x8, Fascia 2x8 |
| 4 | 2x6 | 2x6 @ 78-3/16" (angled) | Barge (fly) rafter 2x6 |
…and 40 more lines, with the angle of every cut, plus a board-by-board cutting plan.
16 build steps, each shown in 3D
- Prepare the site
- Set the skids
- Build the floor frame
- Lay the floor
- Frame the back wall
- Frame the front wall
- Frame the side walls
- Raise and tie the walls
- Frame the roof
- Fascia and barge rafters
- Sheath the roof
- Shingle the roof
- Install the siding
- Trim
- Door and windows
- Paint and finish
Plus the full shopping list with estimated prices, sheet layouts and printable framing drawings for every wall, the floor and a full-size rafter template.
Materials list
The free shopping list for this 10x14 gable shed as shown, with LP SmartSide siding and asphalt shingles: $4,540. 48 items, 145 boards and 29 sheets.
| Item | Qty | Est. |
|---|---|---|
| PT 4x6 x 14' Pressure-treated, ground-contact (UC4A) rated. |
3 boards | $109 |
| PT 2x6 x 14' Pressure-treated, ground-contact (UC4A) rated. |
2 boards | $31 |
| PT 2x6 x 10' Pressure-treated, ground-contact (UC4A) rated. |
12 boards | $132 |
| 2x10 x 12' | 1 board | $19 |
| 2x8 x 16' | 3 boards | $62 |
| 2x6 x 14' | 1 board | $12 |
| 2x6 x 12' | 3 boards | $31 |
| 2x6 x 10' | 3 boards | $26 |
| 2x6 x 8' | 20 boards | $136 |
| 2x4 x 14' | 6 boards | $49 |
| 2x4 x 10' | 15 boards | $87 |
| 2x4 x 92-5/8" precut stud | 59 boards | $235 |
| 1x4 x 12' | 4 boards | $46 |
| 1x4 x 10' | 8 boards | $76 |
| 1x4 x 8' | 5 boards | $38 |
| 23/32" T&G plywood subfloor (Sturd-I-Floor) 4x8 140 sq ft net |
5 sheets | $290 |
| 15/32" CDX plywood roof sheathing 4x8 188.7 sq ft net |
8 sheets | $272 |
| LP SmartSide 38 Series panel 3/8" 4x9 (8" o.c. grooves) 403.4 sq ft net |
14 sheets | $868 |
| LP SmartSide 38 Series panel 3/8" 4x8 (8" o.c. grooves) 33.7 sq ft net |
2 sheets | $104 |
| 3/4" crushed stone, bulk (delivered) 4" compacted pad, 12" past the shed on every side (+15% for compaction) |
2.75 cu yd | $151 |
| Auger ground anchor 30" with strap One at each corner, strapped to the rim joist: a shed on skids can slide or lift in high wind |
4 each | $72 |
| Aluminum drip edge 10 ft Eaves under the underlayment, rakes over it |
6 pieces | $57 |
| Architectural asphalt shingles (3 bundles = 1 square) 189 sq ft of roof + 10% waste |
7 bundles | $294 |
| Shingle starter strip (~100 lin ft) | 1 bundle | $48 |
| Hip & ridge cap shingles (~33 lin ft) | 1 bundle | $68 |
| #15 felt underlayment roll (~400 sq ft) | 1 roll | $30 |
| 1" plastic cap nails (box of 2,000) | 1 box | $24 |
| 1-1/4" galvanized roofing nails 5 lb 4 nails per shingle (6 in high-wind areas) |
1 box | $17 |
| 16d (3-1/2") galvanized framing nails 5 lb (~240) ~1576 nails: 6 per framing piece + 1 per 8" of plate/rim |
7 boxes | $168 |
| #9 x 2-1/2" exterior deck screws 5 lb (~450) ~60 screws per floor sheet |
1 box | $38 |
| Subfloor adhesive 28 oz | 3 tubes | $24 |
| 8d ring-shank galvanized nails 5 lb (~450), roof sheathing ~60 nails per roof sheet |
2 boxes | $52 |
| 8d hot-dip galvanized siding nails 5 lb (~450) ~70 nails per siding panel, 100 more on each door-side panel |
3 boxes | $81 |
| 6d galvanized casing nails 1 lb (~150) 148 lin ft of trim |
2 boxes | $16 |
| 10d (3") galvanized common nails 1 lb (~70) ~246 nails: rafter toenails, jack and nailer studs, collar ties |
4 boxes | $28 |
| Hurricane tie, ZMAX/G185 galvanized for treated lumber (Simpson H2.5AZ or equal) One at every rafter-to-plate seat, plus the floor-to-beam corners |
30 each | $41 |
| 10d x 1-1/2" hot-dip galvanized connector nails 1 lb (~100) Use only connector nails in metal connectors |
3 boxes | $33 |
| 8" heavy-duty T-hinge | 6 each | $54 |
| Safety hasp 4-1/2" | 1 each | $9 |
| Door pull handle | 2 each | $16 |
| Barrel bolt 6" Top and bottom of the fixed leaf |
2 each | $14 |
| Shed window for 24" x 36" rough opening Rough opening 24" x 36" on the left wall |
1 each | $123 |
| Exterior acrylic paint 2 coats over ~535 sq ft |
4 gallons | $192 |
| Exterior paintable caulk 10 oz Seal trim edges and panel joints |
10 tubes | $70 |
| Z-flashing 10 ft Over every door/window head and at horizontal siding joints |
3 pieces | $27 |
| House wrap 9 ft x 100 ft Weather barrier behind the siding (LP requires one behind its panel siding) |
1 roll | $140 |
| 4" window flashing tape 75 ft Seals the window flanges to the house wrap |
1 roll | $22 |
| Strap tie 1-1/4" x 24" (Simpson MSTA24 or equal) Two tie the door header to its king studs |
2 each | $10 |
| Optional / recommended | ||
| Landscape fabric 3 ft x 50 ft Under the gravel to stop weeds |
2 rolls | $44 |
Prices are typical US big-box estimates and vary by region and season. Check your local store.
What a 10x14 shed costs to build with each siding and roof, and where the money goes
Before you build a 10x14
- Weight: about 3,410 to 4,430 lb empty, without its foundation. How much a shed weighs, size by size
- Permit: 140 sq ft, over the building code's 120 sq ft shed exemption but under the residential code's 200, so it depends on which rule your town uses. Do you need a permit for a shed?
- Base: a 12' x 16' gravel pad 4 inches deep, about 2.75 cu yd of stone (3.7 tons), under 3 PT 4x6 skids. Shed foundation options
- Floor: PT 2x6 joists at 16" on center. Floor joist sizes, spacing and spans
- Roof: 6/12 pitch (26.6°). Shed roof pitch chart
Not sure a 10x14 is the right size? What size shed do I need compares all 26 sizes.
Similar sizes
- 10x14 Lean-To Shed plans
140 sq ft · from $4,243 - 12x12 Gable Shed plans
144 sq ft · from $4,436 - 8x16 Gable Shed plans
128 sq ft · from $4,257 - 10x12 Gable Shed plans
120 sq ft · from $4,095 - 10x16 Gable Shed plans
160 sq ft · from $4,905 - 12x14 Gable Shed plans
168 sq ft · from $4,861
Questions
How much does it cost to build a 10x14 gable shed?
Between $4,540 (LP SmartSide siding and asphalt shingles) and $4,980 (board and batten siding and a metal roof) in materials at typical US big-box prices, before tax and delivery. Prices vary by region.
How much lumber do I need for a 10x14 gable shed?
About 145 boards (1072 board feet) and 29 sheets of plywood, OSB or siding, depending on the options you choose.
How tall is a 10x14 gable shed?
About 11' 11-15/16" overall, standing on its gravel base, with walls framed from standard precut studs.
Is a 14x10 shed the same as a 10x14?
Same footprint: 140 square feet whether you write it 10x14, 14x10 or 10 x 14. This plan puts the 10-foot wall at the front with the door. If you want the door on the 14-foot wall, set width 14 and depth 10 in the free calculator and the plan is calculated again for that.
Change the size or options in the free calculator.
Full made-to-measure plans
Every size from 4' to 20', gable or lean-to, as many designs as you like: $37 once, not a book of fixed sizes.
$37 one-time, lifetime access
Get my 10x14 plans, $37Cut list · Board-by-board cutting plan · Shopping list · 3D build steps · Printable drawings · 60-day money-back guarantee
Instant online access after checkout. Works in any web browser on your phone, tablet or computer, and every plan prints. Nothing to download or install.